1997 HUMMER H1 Bolt Pattern
Checking fitment for your vehicle? Below you will find the factory bolt pattern (also known as the lug pattern) for the 1997 HUMMER H1, along with offset and center bore data.
| Bolt Pattern (Lug Pattern) | 8x165.1 (8x6.5") |
|---|---|
| Lug Nut / Bolt Size | N 14x1.50 |
| Center Bore (CB) | 117 mm |
| Offset (ET) | 10 |
| Torque Specs | 140 ft-lbs (190 Nm) |
1997 H1 — Year-Specific Fitment Context
The 1997 HUMMER H1 is in year 5 of 14 using the 8x165.1 pattern (1993–2006). Wheels from any 1993–2006 HUMMER H1 are cross-compatible with the 1997 model.
HUMMER H1 Bolt Pattern by Year
The table below shows how the H1's wheel specifications have changed over the years. The 1997 model year is highlighted.
Fitment Notes
The 1997 HUMMER H1 has a bolt pattern of 8x165.1.
Imperial Conversion: This bolt pattern is commonly referred to as 8x6.5" in imperial units. When searching for aftermarket wheels, you may see them listed as 8x6.5".
This means it is a 8 lug pattern with a circle diameter of 165.1mm. When shopping for aftermarket wheels, ensure the "lug pattern" or "PCD" matches these numbers.
Year-to-Year Fitment Context
In our dataset, HUMMER H1 appears from 1993 to 2006 (13 model years).
Across recorded model years, this model generally keeps the same bolt pattern.
- Observed bolt-pattern variants for this model: 1
- Observed center-bore variants for this model: 1
- Observed lug-size variants for this model: 1
- Observed total offset span across years: 0.0 mm
8x165.1 Pattern Context
This bolt pattern appears on 846 vehicles in our current database and is considered common.
Examples of other vehicles using 8x165.1:
1997 HUMMER H1 — Frequently Asked Questions
What is the bolt pattern for a 1997 HUMMER H1?
The 1997 HUMMER H1 uses a 8x165.1 bolt pattern (also called lug pattern or PCD). The center bore is 117mm and the offset is 10mm.
What other years of HUMMER H1 have the same bolt pattern as the 1997?
The HUMMER H1 uses the 8x165.1 pattern from 1993 through 2006. Wheels from any of these model years are dimensionally compatible with the 1997, provided the offset and center bore also match.
Can I use spacers on my 1997 HUMMER H1?
Yes, but ensure the wheel spacers match the 8x165.1 bolt pattern and 117mm center bore. Also verify that you have enough thread engagement for your N 14x1.50 hardware.
What is the PCD for a 1997 HUMMER H1?
PCD stands for Pitch Circle Diameter, which is the same as the bolt pattern. For the 1997 H1, the PCD is 8x165.1.
What does 10mm offset mean for the 1997 H1?
An offset of 10mm means the wheel's mounting surface is 10mm away from its centerline. Changing this value drastically can affect suspension geometry and wheel bearing wear on your HUMMER.
How do I measure the bolt pattern on my 1997 HUMMER?
The 1997 H1 uses a 8x165.1 pattern. For 4, 6, or 8-lug wheels, measure center-to-center across opposite holes. For 5-lug, measure from the center of one hole to the back of the opposite hole.
Fitment Checklist Before You Buy Wheels
- Torque lugs in a star pattern to 140 ft-lbs (190 Nm), then re-check torque after 50-100 km (30-60 miles).
Editorial Fitment Notes
HUMMER H1 is generally consistent in bolt-pattern records across model years, but offset and hardware should still be validated before purchase.
- Observed production years in our database: 1993-2006 (13 model years).
- Observed bolt-pattern variants: 1 (8x165.1).
- Observed total offset span across years: 0.0 mm.
- Observed center-bore variants: 1 | lug-size variants: 1.
Data Quality & Review
Source note: Compiled from manufacturer fitment references, historical wheel data, and internal normalization rules.
Last reviewed: 2026-05-26 | Reviewed by: Bolt Pattern HQ Editorial Team
If you find a discrepancy for 1997 HUMMER H1, please report it via our About page contact so we can verify and update this record.