2009 HUMMER H2 Bolt Pattern
Checking fitment for your vehicle? Below you will find the factory bolt pattern (also known as the lug pattern) for the 2009 HUMMER H2, along with offset and center bore data.
| Bolt Pattern (Lug Pattern) | 8x165.1 (8x6.5") |
|---|---|
| Lug Nut / Bolt Size | N 14x1.50 |
| Center Bore (CB) | 117 mm |
| Offset (ET) | 10 |
| Torque Specs | 140 ft-lbs (190 Nm) |
Imperial Match: 8x165.1 is commonly referred to as 8x6.5" in US Standard.
2009 H2 — Year-Specific Fitment Context
The 2009 model year is the final year of the HUMMER H2's 8x165.1 bolt pattern run (since 2003). Wheels from any 2003–2009 HUMMER H2 are cross-compatible with the 2009 model.
HUMMER H2 Bolt Pattern by Year
The table below shows how the H2's wheel specifications have changed over the years. The 2009 model year is highlighted.
8x165.1 Pattern Context
This bolt pattern appears on 846 vehicles in our current database and is considered common.
Examples of other vehicles using 8x165.1:
Expert Buying Guide for 2009 HUMMER H2
The 2009 HUMMER H2 uses an 8x165.1 bolt pattern with a 117mm center bore. Aftermarket wheels often have a larger bore, requiring hub-centric rings to prevent vibration and ensure proper load distribution. Offset is critical; the factory 10mm offset should be maintained within ±5mm to avoid rubbing or suspension interference. Always use the correct lug nuts: 14x1.50 thread pitch with a conical (60-degree) seat. Ball-seat or shank-style nuts can cause wheel loosening. Re-torque after 50 miles of driving.
Historical Fitment Data Reference
In our dataset, HUMMER H2 appears from 2003 to 2009 (7 model years). Across recorded model years, this model generally keeps the same bolt pattern.
- Observed bolt-pattern variants for this model: 1
- Observed center-bore variants for this model: 1
- Observed lug-size variants for this model: 1
- Observed total offset span across years: 0.0 mm
Quick Tips & Safety Warnings
- ✅ Re-torque lug nuts to 140 ft-lbs after 50 miles, then periodically check.
- ✅ Hub-centric rings must be 117mm ID to 8x165.1 hub OD; plastic rings suffice for street use.
- ✅ Avoid wheels with offset below 5mm or above 15mm to prevent brake caliper or fender contact.
- ⚠️ Torque lugs in a star pattern to 140 ft-lbs (190 Nm), then re-check torque after 50-100 km (30-60 miles).
Ready to upgrade or perform maintenance?
🛒 Shop Tools & Accessories on AmazonAs an Amazon Associate, I earn from qualifying purchases.
2009 HUMMER H2 — Frequently Asked Questions
What is the bolt pattern for a 2009 HUMMER H2?
The 2009 HUMMER H2 uses a 8x165.1 bolt pattern (also called lug pattern or PCD). The center bore is 117mm and the offset is 10mm.
What other years of HUMMER H2 have the same bolt pattern as the 2009?
The HUMMER H2 uses the 8x165.1 pattern from 2003 through 2009. Wheels from any of these model years are dimensionally compatible with the 2009, provided the offset and center bore also match.
What is the factory wheel offset for a 2009 HUMMER H2?
The OEM offset for the 2009 H2 is typically around 10mm. Depending on wheel width, a deviation of ±5mm is usually acceptable, but verify suspension clearance.
How tight should I torque the lug nuts on a 2009 HUMMER H2?
Refer to your owner's manual for exact specs, but always tighten the N 14x1.50 hardware in a star or crisscross pattern. Re-torque after the first 50 miles of driving.
What is the center bore of a 2009 HUMMER H2?
The factory center bore (hub bore) for the 2009 HUMMER H2 is 117mm. If your aftermarket wheels have a larger hub bore, you will need hub-centric rings to prevent vibration.
What lug nut size does the 2009 HUMMER H2 use?
The 2009 HUMMER H2 uses N 14x1.50 lug nuts. Always verify the thread pitch and seat type (cone, ball, or flat) match your aftermarket wheels.
Need more vehicle fitment data?
Access our complete, raw JSON/CSV database of over 11,000+ vehicles for your next app or project.
Get the Full Dataset