1996 Honda Prelude Bolt Pattern
Quick Answer: The factory bolt pattern (lug pattern) for a 1996 Honda Prelude is 4x114.3. It has a center bore of 64.1 mm, an offset range of 50, and utilizes N 12x1.50 (Ball seat, 19mm hex) fasteners tightened to 80 ft-lbs (108 Nm).
1996 Honda Prelude Wheel Fitment Specs
| Bolt Pattern (Lug Pattern) | 4x114.3 |
|---|---|
| Center Bore (Hub Bore) | 64.1 mm |
| Offset Range (ET) | 50 |
| Thread Size (Lug Nut / Bolt) | N 12x1.50 |
| Fastener Seat Type | Radius / Spherical (Ball Seat) |
| Lug Wrench / Socket Hex Size | 19mm |
| Wheel Torque Specs | 80 ft-lbs (108 Nm) |
1996 Prelude β Year-Specific Fitment Context
The 1996 Honda Prelude is in year 5 of 7 using the 4x114.3 pattern (1992β1998). Wheels from any 1992β1998 Honda Prelude are cross-compatible with the 1996 model. Across its full production run (1992β2001), the Prelude has also used: 5x114.3.
Honda Prelude Bolt Pattern by Year
The table below shows how the Prelude's wheel specifications have changed over the years. The 1996 model year is highlighted.
1996 Honda Prelude Wheel Interchange & Donor Fitment Guide (4x114.3)
The 4x114.3 bolt pattern is shared by 175 vehicles in our database (uncommon). For safe wheel swaps on the 1996 Honda Prelude, donor rims must match the 4x114.3 PCD and have a center bore of at least 64.1 mm:
DIRECT HUB MATCH Same 4x114.3 Pattern & Exact 64.1mm Center Bore (No Hub Rings Needed)
| Compatible Donor Vehicle | Center Bore | OEM Offset (ET) | Lug Thread & Seat |
|---|---|---|---|
| 1992 Honda Accord | 64.1 mm (Exact) | 50 | N 12x1.50 (Ball) |
| 1997 Honda CR-V | 64.1 mm (Exact) | 50 | N 12x1.50 (Ball) |
HUB RING FITMENT Same 4x114.3 Pattern with Larger Center Bore (Hub-Centric Ring Required)
| Donor Vehicle | Donor Bore | Required Hub Ring (OD β ID) | OEM Offset (ET) |
|---|---|---|---|
| 2003 Hyundai Sonata | 67.1 mm | 67.1mm β 64.1mm |
46 |
| 2001 Kia Optima | 67.1 mm | 67.1mm β 64.1mm |
46 |
| 2006 Kia Optima (2006.5) | 67.1 mm | 67.1mm β 64.1mm |
46 |
| 1992 Mitsubishi Galant | 67.1 mm | 67.1mm β 64.1mm |
46 |
| 2005 Mitsubishi Lancer | 67.1 mm | 67.1mm β 64.1mm |
46 |
| 1995 Nissan 200SX | 66.1 mm | 66.1mm β 64.1mm |
44 |
Expert Buying Guide for 1996 Honda Prelude
For your 1996 Honda Prelude, the 4x114.3 bolt pattern and 64.1mm center bore are critical. Aftermarket wheels often have a larger center bore, so hub-centric rings are mandatory to prevent vibrations and ensure proper load distribution. The factory offset is 50mm; deviations beyond Β±5mm may cause rubbing or clearance issues. Always use lug nuts with the correct thread pitch (12x1.5) and seat typeβconical (60-degree) seats are standard for Prelude wheels. Avoid ball-seat lug nuts as they can loosen. Re-torque after 50-100 miles to maintain clamping force.
Historical Fitment Data Reference
In our dataset, Honda Prelude appears from 1992 to 2001 (10 model years). Across model years, this model appears with 2 bolt patterns (4x114.3, 5x114.3).
- Observed bolt-pattern variants for this model: 2
- Observed center-bore variants for this model: 1
- Observed lug-size variants for this model: 1
- Observed total offset span across years: 0.0 mm
Quick Tips & Safety Warnings
- β Re-torque lug nuts to 80 ft-lbs after 50-100 miles of driving.
- β If using aftermarket wheels, ensure hub-centric rings are installed to match the 64.1mm bore.
- β Double-check that the wheel offset stays within 45-55mm to avoid rubbing the strut or fender.
- β οΈ Verify thread pitch before installation; M12x1.25 and M12x1.5 are not interchangeable.
- β οΈ Torque lugs in a star pattern to 80 ft-lbs (108 Nm), then re-check torque after 50-100 km (30-60 miles).
- β οΈ This model has multiple bolt-pattern records across years. Match wheels to exact year/trim before purchase.
1996 Honda Prelude β Frequently Asked Questions
What is the bolt pattern for a 1996 Honda Prelude?
The 1996 Honda Prelude uses a 4x114.3 bolt pattern (also called lug pattern or PCD). The center bore is 64.1mm and the offset is 50mm.
What other years of Honda Prelude have the same bolt pattern as the 1996?
The Honda Prelude uses the 4x114.3 pattern from 1992 through 1998. Wheels from any of these model years are dimensionally compatible with the 1996, provided the offset and center bore also match.
Will wheels from another Honda fit my 1996 Prelude?
Only if they share the exact same 4x114.3 bolt pattern, a compatible offset, and a center bore equal to or larger than 64.1mm.
What is the center bore of a 1996 Honda Prelude?
The factory center bore (hub bore) for the 1996 Honda Prelude is 64.1mm. If your aftermarket wheels have a larger hub bore, you will need hub-centric rings to prevent vibration.
How do I measure the bolt pattern on my 1996 Honda?
The 1996 Prelude uses a 4x114.3 pattern. For 4, 6, or 8-lug wheels, measure center-to-center across opposite holes. For 5-lug, measure from the center of one hole to the back of the opposite hole.
Do 1996 Honda Preludes use lug bolts or lug nuts?
The 1996 Prelude requires N 12x1.50 hardware. Check your specific trim to ensure you use the correct conical or spherical seating.
Need Full Fitment Data in Bulk?
Stop scraping or looking up cars one by one. Import 12,400+ verified vehicle specs (1992β2025) directly into your Shopify store, inventory system, or custom automotive software.
Explore Master Database (CSV) →