2010 Dodge Caliber Bolt Pattern
Checking fitment for your vehicle? Below you will find the factory bolt pattern (also known as the lug pattern) for the 2010 Dodge Caliber, along with offset and center bore data.
| Bolt Pattern (Lug Pattern) | 5x114.3 (5x4.5") |
|---|---|
| Lug Nut / Bolt Size | N 12x1.50 |
| Center Bore (CB) | 67.1 mm |
| Offset (ET) | 41 |
| Torque Specs | 80 ft-lbs (108 Nm) |
2010 Caliber — Year-Specific Fitment Context
The 2010 Dodge Caliber is in year 4 of 6 using the 5x114.3 pattern (2007–2012). Wheels from any 2007–2012 Dodge Caliber are cross-compatible with the 2010 model.
Dodge Caliber Bolt Pattern by Year
The table below shows how the Caliber's wheel specifications have changed over the years. The 2010 model year is highlighted.
Fitment Notes
The 2010 Dodge Caliber has a bolt pattern of 5x114.3.
Imperial Conversion: This bolt pattern is commonly referred to as 5x4.5" in imperial units. When searching for aftermarket wheels, you may see them listed as 5x4.5".
This means it is a 5 lug pattern with a circle diameter of 114.3mm. When shopping for aftermarket wheels, ensure the "lug pattern" or "PCD" matches these numbers.
Year-to-Year Fitment Context
In our dataset, Dodge Caliber appears from 2007 to 2012 (6 model years).
Across recorded model years, this model generally keeps the same bolt pattern.
- Observed bolt-pattern variants for this model: 1
- Observed center-bore variants for this model: 1
- Observed lug-size variants for this model: 1
- Observed total offset span across years: 0.0 mm
5x114.3 Pattern Context
This bolt pattern appears on 2902 vehicles in our current database and is considered very common.
Examples of other vehicles using 5x114.3:
2010 Dodge Caliber — Frequently Asked Questions
What is the bolt pattern for a 2010 Dodge Caliber?
The 2010 Dodge Caliber uses a 5x114.3 bolt pattern (also called lug pattern or PCD). The center bore is 67.1mm and the offset is 41mm.
What other years of Dodge Caliber have the same bolt pattern as the 2010?
The Dodge Caliber uses the 5x114.3 pattern from 2007 through 2012. Wheels from any of these model years are dimensionally compatible with the 2010, provided the offset and center bore also match.
What is the PCD for a 2010 Dodge Caliber?
PCD stands for Pitch Circle Diameter, which is the same as the bolt pattern. For the 2010 Caliber, the PCD is 5x114.3.
Can I use spacers on my 2010 Dodge Caliber?
Yes, but ensure the wheel spacers match the 5x114.3 bolt pattern and 67.1mm center bore. Also verify that you have enough thread engagement for your N 12x1.50 hardware.
What is the factory wheel offset for a 2010 Dodge Caliber?
The OEM offset for the 2010 Caliber is typically around 41mm. Depending on wheel width, a deviation of ±5mm is usually acceptable, but verify suspension clearance.
What lug nut size does the 2010 Dodge Caliber use?
The 2010 Dodge Caliber uses N 12x1.50 lug nuts. Always verify the thread pitch and seat type (cone, ball, or flat) match your aftermarket wheels.
Fitment Checklist Before You Buy Wheels
- Verify thread pitch before installation; M12x1.25 and M12x1.5 are not interchangeable.
- Confirm bolt pattern carefully. 5x114.3 is often confused with other common 5-lug patterns.
- Torque lugs in a star pattern to 80 ft-lbs (108 Nm), then re-check torque after 50-100 km (30-60 miles).
Editorial Fitment Notes
Dodge Caliber is generally consistent in bolt-pattern records across model years, but offset and hardware should still be validated before purchase.
- Observed production years in our database: 2007-2012 (6 model years).
- Observed bolt-pattern variants: 1 (5x114.3).
- Observed total offset span across years: 0.0 mm.
- Observed center-bore variants: 1 | lug-size variants: 1.
Data Quality & Review
Source note: Compiled from manufacturer fitment references, historical wheel data, and internal normalization rules.
Last reviewed: 2026-05-26 | Reviewed by: Bolt Pattern HQ Editorial Team
If you find a discrepancy for 2010 Dodge Caliber, please report it via our About page contact so we can verify and update this record.