2020 Kia Cadenza Bolt Pattern
Checking fitment for your vehicle? Below you will find the factory bolt pattern (also known as the lug pattern) for the 2020 Kia Cadenza, along with offset and center bore data.
| Bolt Pattern (Lug Pattern) | 5x114.3 (5x4.5") |
|---|---|
| Lug Nut / Bolt Size | 12x1.5 |
| Center Bore (CB) | 67.1 mm |
| Offset (ET) | 35-50 |
| Torque Specs | 80 ft-lbs (108 Nm) |
Imperial Match: 5x114.3 is commonly referred to as 5x4.5" in US Standard.
2020 Cadenza — Year-Specific Fitment Context
The 2020 model year is the final year of the Kia Cadenza's 5x114.3 bolt pattern run (since 2014). Wheels from any 2014–2020 Kia Cadenza are cross-compatible with the 2020 model.
Kia Cadenza Bolt Pattern by Year
The table below shows how the Cadenza's wheel specifications have changed over the years. The 2020 model year is highlighted.
5x114.3 Pattern Context
This bolt pattern appears on 2902 vehicles in our current database and is considered very common.
Examples of other vehicles using 5x114.3:
Expert Buying Guide for 2020 Kia Cadenza
For your 2020 Kia Cadenza, the bolt pattern is 5x114.3mm with a critical center bore of 67.1mm. Aftermarket wheels often have a larger bore, so hub-centric rings (67.1mm ID to wheel bore OD) are mandatory to prevent vibration and ensure proper load transfer. Offset must stay within 35-50mm; deviating risks rubbing or poor handling. Use only 12x1.5 lug nuts with the correct seat type—conical (60-degree) or ball seat—as specified by the wheel manufacturer. Never mix seat types; improper seating can cause wheel loss. Always torque to manufacturer specs (typically 80-90 ft-lbs) and re-torque after 50 miles.
Historical Fitment Data Reference
In our dataset, Kia Cadenza appears from 2014 to 2020 (7 model years). Across recorded model years, this model generally keeps the same bolt pattern.
- Observed bolt-pattern variants for this model: 1
- Observed center-bore variants for this model: 1
- Observed lug-size variants for this model: 1
- Observed total offset span across years: 85.0 mm
Quick Tips & Safety Warnings
- ✅ Re-torque lug nuts after 50 miles of driving to account for settling.
- ✅ Verify wheel bore diameter; if larger than 67.1mm, install hub-centric rings to avoid vibrations.
- ✅ Check that aftermarket wheels have adequate brake caliper clearance, especially with larger rotors.
- ⚠️ Verify thread pitch before installation; M12x1.25 and M12x1.5 are not interchangeable.
- ⚠️ Confirm bolt pattern carefully. 5x114.3 is often confused with other common 5-lug patterns.
- ⚠️ This fitment uses a wide offset range. Check brake clearance and fender clearance before buying wheels.
- ⚠️ Torque lugs in a star pattern to 80 ft-lbs (108 Nm), then re-check torque after 50-100 km (30-60 miles).
Ready to upgrade or perform maintenance?
🛒 Shop Tools & Accessories on AmazonAs an Amazon Associate, I earn from qualifying purchases.
2020 Kia Cadenza — Frequently Asked Questions
What is the bolt pattern for a 2020 Kia Cadenza?
The 2020 Kia Cadenza uses a 5x114.3 bolt pattern (also called lug pattern or PCD). The center bore is 67.1mm and the offset is 35-50mm.
What other years of Kia Cadenza have the same bolt pattern as the 2020?
The Kia Cadenza uses the 5x114.3 pattern from 2014 through 2020. Wheels from any of these model years are dimensionally compatible with the 2020, provided the offset and center bore also match.
What is the PCD for a 2020 Kia Cadenza?
PCD stands for Pitch Circle Diameter, which is the same as the bolt pattern. For the 2020 Cadenza, the PCD is 5x114.3.
How tight should I torque the lug nuts on a 2020 Kia Cadenza?
Refer to your owner's manual for exact specs, but always tighten the 12x1.5 hardware in a star or crisscross pattern. Re-torque after the first 50 miles of driving.
Will wheels from another Kia fit my 2020 Cadenza?
Only if they share the exact same 5x114.3 bolt pattern, a compatible offset, and a center bore equal to or larger than 67.1mm.
Can I put aftermarket wheels on my 2020 Kia Cadenza?
Absolutely. Just ensure the aftermarket wheels have a 5x114.3 bolt pattern, an offset near 35-50mm, and a center bore of at least 67.1mm (using hub rings if larger).
Need more vehicle fitment data?
Access our complete, raw JSON/CSV database of over 11,000+ vehicles for your next app or project.
Get the Full Dataset